Tank leaking from the bottom seam
We shut off the water, drain the tank, and install a new unit with a fresh drain pan. If the leak reached the subfloor, we flag it so you can dry it out before mold sets in.
When your old tank starts leaking or the hot water runs out before your shower does, water heater installation Annapolis MD homeowners trust means a code-correct swap done in a day. We handle the Anne Arundel County Plumbing Permit, haul away the old unit, and pressure-test every connection before we leave. Whether you need a 40-gallon tank or a high-efficiency Navien, we size it to your house and your budget.

Water heater installation Annapolis MD is the licensed removal of your old tank or tankless unit and the code-compliant install of a new one, including the permit, the drain pan, the expansion tank, and the final safety check. It is not a swap-and-go job. We shut off the gas or breaker, drain the old tank, cut out corroded copper pipe or brittle PEX tubing, and rebuild the connections with new pipe fittings and Teflon tape. Then we fill, purge the air, and test the temperature-pressure relief valve before you ever touch the tap.
Most Annapolis homeowners call us for one of three reasons: the tank is 10 to 12 years old and rusting at the seams, the pilot keeps going out, or a family of four keeps running cold. If you are searching for water heater installation near me Annapolis MD because you woke up to a puddle in the garage, we can often get a new unit in the same day. We also handle water heater replacement Annapolis MD for homeowners upgrading to a larger tank or a heat-pump model.
Every install we do covers the essentials: the unit, the permit, the haul-away, and the safety check. Here is what is in the standard price and what we handle on site.
We supply the new tank or tankless unit plus fresh flexible connectors, pipe fittings, and Teflon tape. We do not reuse old shut-off valves or corroded nipples.
We pull the Anne Arundel County Plumbing Permit and meet the inspector on site. You get the signed-off paperwork for your records and your insurance.
The old tank goes on our truck and off your property. No curbside pile, no trip to the dump, no disposal fee tacked on later.
We install a new drain pan and test the temperature-pressure relief valve and the expansion tank. These are the parts that prevent a small leak from becoming a flooded floor.
We fill the tank, purge the air, and run hot water at every fixture. Then we show you the shut-off, the settings, and the warranty terms before we pack up.
You call, we ask about the house, the number of bathrooms, and the fuel type. We give you a price range over the phone and book a window, usually same-day or next-day. If you are replacing an emergency failure, tell us and we move you up.
The technician checks the old unit, the venting, the gas line or breaker, and the space. We confirm the size and model, show you the price in writing, and get your okay before any work starts. No surprises on the invoice.
We shut off the water and fuel, drain the old tank with a hose, and disconnect the lines. The old unit goes on the truck for haul-away. We inspect the floor and the shut-off valve and replace anything that will not survive the new install.
The new unit goes in level, with a new drain pan, new flexible connectors, and a fresh Teflon-taped fitting set. We solder or press the copper, fill the tank, purge the air, and run the hot water at every fixture until it is clear and hot.
We schedule the Anne Arundel County inspection, meet the inspector on site, and hand you the warranty paperwork. Before we leave, we show you the shut-off, the relief valve, and the settings so you know how to kill the water in a hurry.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Clean cuts and leak-free copper joints. We also carry a press tool for tight spots where a torch is not safe.
Removing old nipples and tightening new connections. We replace every fitting we touch rather than reusing corroded parts.
Tracing a leak to the tank, the pipe, or the slab before we commit to a replacement.
Crimping PEX tubing and copper press fittings in tight mechanical closets where a torch would be a fire risk.
Clearing sediment and scale from the lines after a tank swap so hot water reaches every fixture.
A 12-year-old 40-gallon tank in Eastport was leaking from the bottom seam and leaving rust stains in the drain pan. The family of four was running out of hot water by the second shower.
We installed a new 50-gallon Rheem with a fresh drain pan, new connectors, and a permit. Hot water now lasts through four showers, and the leak is gone. The job took three hours.
A homeowner in Parole wanted endless hot water for a growing family. The old 50-gallon tank took up most of the garage wall and could not keep up with two showers and a dishwasher at once.
We installed a Navien tankless unit, upgraded the gas line, and ran new venting. The wall space came back, and the hot water never runs out. The install took seven hours.
A frozen pipe burst in a West Annapolis garage and soaked the water heater's electrical connection. The tank was 11 years old and the homeowner had no hot water.
We repaired the burst pipe, dried the area, and installed a new 40-gallon unit with a fresh breaker and drain pan. The relief valve and expansion tank were tested. Hot water was back the same day.
If you are searching for a way to replace old water heater Annapolis Maryland, these are the failure modes we see most often and how a new install fixes them.
Ask a pro →We shut off the water, drain the tank, and install a new unit with a fresh drain pan. If the leak reached the subfloor, we flag it so you can dry it out before mold sets in.
We flush the old tank to confirm the diagnosis, then size a new unit to your household. A 50 gallon water heater installation Annapolis MD usually solves the problem for a family of four.
We test the gas line and venting before we sell you a new heater. If the unit is sound, we repair it. If it is at end of life, we install a new Rheem or Bradford White unit with a fresh vent.
We check the anode rod and the tank interior. If corrosion has started, replacement is the only fix. We install a new unit and check your water pressure so the next tank lasts.
$1,200 - $4,500 depending on unit and scope
Typical 2026 pricing in this area runs $1,200 to $2,400 for a standard tank install, including the unit, permit, and haul-away. Tankless and heat-pump models run $2,800 to $4,500 because of venting and electrical upgrades. The price depends on tank size, fuel type, and how much of the old plumbing needs to be rebuilt. We quote the full job before we start, so the number you hear is the number you pay.
A new water heater lasts 10 to 15 years, and a permitted, code-correct install protects your insurance and your resale. The cheapest quote often skips the permit and the drain pan, which is exactly where the problems start.
A 40-gallon tank costs less than a 65-gallon or a heat-pump unit. Higher-efficiency models cost more up front but cut monthly bills.
Gas units need venting and a gas line check. Electric units need a breaker and wire sized correctly. Tankless gas units often need a gas line upgrade.
Older homes may need a new vent, a power-vent kit, or a chimney liner. These are code requirements, not upsells, and they affect the final price.
Anne Arundel County charges a permit fee, and we include it in the quote. Skipping the permit saves a little now and costs more at resale.
“Our 12-year-old tank started leaking on a Friday morning. I called and they had a new 50-gallon Rheem in by 2 p.m. The tech pulled the permit, hauled the old unit away, and showed me how to shut the water off. No mess left behind and the price matched the quote.”
Karen M.Homeowner, Eastport
✓ Verified“The mechanical closet in our 1920s house is tiny, and two other companies said they could not fit a new tank. These guys measured, found a short Bradford White, and rebuilt the copper without tearing up the wall. Inspection passed the first time.”
Dave R.Homeowner, Historic District
✓ Verified“We switched to a Navien tankless and the crew handled the venting and gas line upgrade in one day. They walked us through the temperature settings and the annual flush. Hot water never runs out now, even with two teenagers.”
Priya S.Homeowner, Parole
✓ VerifiedMost standard tank installs run $1,200 to $2,400 in 2026, including the unit, permit, and haul-away. Tankless and heat-pump models run higher, often $2,800 to $4,500, because of venting and electrical upgrades. The cost to install water heater in Annapolis Maryland depends on tank size, fuel type, and whether the old unit comes out cleanly.
A standard tank swap takes two to four hours from arrival to hot water. Tankless conversions take longer, usually six to eight hours, because we run new gas lines or electrical. If you book same day water heater installation Annapolis MD, plan on the crew being at your house for most of the afternoon.
A family of two usually needs a 40-gallon tank, three to four people need 50 gallons, and five or more need 65 to 80 gallons. If you have two bathrooms and a dishwasher, lean toward 50 gallons. We check your fixture count and peak-hour use before we recommend a size.
Yes. Anne Arundel County requires a plumbing permit for a water heater replacement, and the work must be inspected. We pull the permit, meet the inspector, and keep the paperwork for you. Skipping the permit can void your homeowner insurance and create a problem when you sell the house.
Cold showers do not fix themselves. Call us with your address and the old tank size, and we will give you a price and a window. Licensed, insured, and permitted through Anne Arundel County.
Book My Install +1 (831) 293-1204 →Call us at +1 (831) 293-1204 or email plumberannapolismd@gmail.com. We answer the phone 24/7 for emergencies and schedule same-day or next-day visits for non-urgent work. Tell us what's wrong and your address, and we'll give you a time window and a price range before we head out.